QSI 683WSG Mono CCD Camera with STi Thread
QSI 683WSG Mono CCD Camera with STi Thread
The QSI 683WSG CCD camera uses the popular 8.3-megapixel TrueSense KAF-8300 full frame CCD imaging sensor. The KAF-8300 offers a large field of view in cameras using standard 1.25" filters. The 5.4-micron pixel size provides extremely high resolution. The sensor uses true two-phase charge transfer technology with a transparent gate that significantly increases optical response compared to traditional front-illuminated full frame sensors. The superb imaging performance of this 683 WSG camera by QSI is wrapped in an attractive, compact design with outstanding power efficiency and investment protecting upgradeability. The refined engineering and impressive fit, finish, and attention to detail will surpass your highest expectations. The QSI 683wsg camera system is supported by industry-leading astronomy and microscopy image acquisition software, and a full camera control API is available for creating custom Windows or Linux applications.
- QSI 683 camera comes with a TrueSense KAF-8300 sensor, with 8.3 MegaPixels and a peak QE of 60%
- WSG models include an Integrated Guider Port (IGP). This one comes with threads for the SBIG STi
- 5 Position Color Filter Wheel comes ready for your threaded 1.25" filters
- High-speed USB 2.0 with 16-bit output
- Dual read rates of 800 kHz and 8 MHz with virtually undetectable read noise
- Electronic shutter speeds to 100 microseconds
- Internal, even-illumination mechanical shutter for dark & bias frames
- Intelligent, programmable two stage TEC cooling to 45???C below ambient
- ASCOM compatible Windows COM API
- Linux drivers and API
The QSI 683wsg camera employs a TrueSense KAF-8300 (formerly by Kodak) full frame CCD image sensor with micro-lensing technology. The KAF-8300 has an excellent quantum efficiency between 350 nm and 1000 nm with a peak QE of 57%. Low dark current and high pixel charge capacity result in a dynamic range exceeding 70 dB. The sensor has anti-blooming protection and a fast electronic shutter. Microlenses cover the surface of the CCD to focus the light into each 5.4-micron pixel, thereby increasing the optical photon response.
- CCD Architecture: Full Frame
- Microlensing Technology: Yes
- Anti-Blooming: Yes - 1000X suppression
- Imager Size: 17.96 mm Wide x 13.52 mm High
- Pixel Array: 3326 x 2507 active pixels
- Total Number of Pixels: 8.3 megapixels
- Pixel Size: 5.4-micron
- Quantum Efficiency: Peak: 57%, 400 nm 38%
- Dark Current Doubling: 5.8 degrees C
- Intrinsic Read Noise: 8 electrons RMS
- Dynamic Range: 70 dB
The QSI 683wsg has a very efficient custom 2-stage Thermoelectric Cooler (TEC) subsystem. Intelligent, programmable cooling fans are integrated into the rear of the camera body to remove the heat generated by the cooler. Typically, forced air cooling lowers the regulated CCD temperature by up to 45???C below ambient utilizing 85% power. Tight ??????ñ 0.1???C temperature regulation is maintained at temperature settings of 10???C below ambient and lower. A slim liquid heat exchanger (sold separately) can be attached to the rear of the camera body to increase the cooling further, up to 55???C below the temperature of the circulating fluid.
The cooled CCD image sensor is positioned in a hermetically sealed environmental chamber and covered with an anti-reflection precision optical window. The sealed chamber is purged with an ultra dry noble gas to increase heat conduction and eliminate the possibility of frost forming inside the chamber. To extend the useful period before re-purging is required, a user-rechargeable micro-sieve desiccant is employed to scavenge water molecules that enter the chamber. It is located behind a sub-micron, gas-permeable membrane to prevent particulate contamination of the CCD chamber.
The QSI 600 Series WSG cameras provide a solution to the problems normally associated with guiding by integrating a Guider Port directly into the camera body. The pick-off prism is designed to sit in front of the filters so that you will always have all of the star's light available for guiding.
The large 1/2" square pick-off prism of the integrated guide port is optimally positioned close to the internal filter wheel, supporting the use of guide cameras with large sensors, while preventing any vignetting of the main sensor, even with very fast optical systems. This Integrated Guide Port (IGP) is designed to support the SBIG STi auto guider.
The threaded adapter sits on top of the focus ring and allows the guide camera to be rotated to any position. The focus ring threads onto the focus base to allow 3 mm of travel when focusing the guide camera. Once focus is achieved, the focus ring is locked with a set screw. The guide camera can still be rotated manually if desired without changing the focus. The end result is a rigid, easily focused guide camera that will not move or flex while your mount tracks the apparent motion of the night sky.
|Binning Modes||1x1 and 2x2 and 3x3 and 4x4 and 5x5 and 6x6 and 7x7 and 8x8 and 9x9|
|Blue Enhanced Sensor||no|
|Camera Series||QSI 600|
|Dark Current||<0.1 electron per second at 0 degreesC|
|Dimensions||W5.86" x H5.56" x D2.50"|
|Front or Back Illumination||Front|
|Integrated Guider||No but includes Integrated Guide Po|
|Operating System Compatibility||Linux (3rd Party) & Windows|
|Pixel Array||3326 x 2504|
|Pixel Size||5.4 microns|
|Quantum Efficiency||57% peak|
|Sensor Design||Full Frame|
|Sensor Manufacturer||Truesense formerly Kodak|
|Shutter Type||Digital & Mechanical|
|Single or Dual Sensor||Single|
QUESTIONS & ANSWERS
Have a Question?
Be the first to ask a question about this.