QSI 632WSG Monochrome CCD Camera - Mechanical Shutter, 5-Position CFW & Integrated Guide Port
QSI 632WSG Monochrome CCD Camera - Mechanical Shutter, 5-Position CFW & Integrated Guide PortThis 632WSG Monochrome CCD Camera by QSI includes a Mechanical Shutter, 5-Position CFW, and an Integrated Guide Port.
About the QSI 632 WSG Monochrome CCD Camera:
The QSI 632wsg CCD camera uses a 3.2 megapixel Kodak (now TrueSense) full frame CCD imaging sensor as its light-gathering source. The KAF-3200ME offers amazingly high quantum efficiency, with a peak EQ of over 80-percent. The sensor uses a true two-phase charge transfer technology with a transparent gate that significantly increases optical response compared to traditional front-illuminated full frame sensors. The superb imaging performance of the 632 WSG camera is wrapped in an attractive, compact design with outstanding power efficiency and investment protecting your ability to upgrade. The refined engineering and impressive fit, finish and attention to detail will surpass your highest expectations.The QSI 632wsg camera system is supported by industry-leading astronomy and microscopy image acquisition software, and a full camera control API is available for creating custom Windows or Linux applications.
QSI 632WSG CCD Camera Highlights:
*The QSI 632 camera comes with a TrueSense KAF-04022 monochrome sensor with 3.2MP, micro lens technology and anti-blooming protection.
*All WSG models include an Integrated Guider Port (IGP)
*A 5-Position Color Filter Wheel comes ready for your threaded 1.25-inch filters
*High speed USB 2.0 with 16-bit output
*Dual read rates of 800kHz and 8MHz with virtually undetectable read noise
*Electronic shutter speeds to 100 microseconds
*Internal, even-illumination mechanical shutter for dark & bias frames
*Intelligent, programmable two stage TEC cooling to 45C below ambient
*ASCOM-compatible Windows COM API
*Linux drivers and API
About the KAF-3200ME Imaging Sensor:
The QSI 632wsg camera employs a Kodak KAF-3200ME full frame CCD image sensor with microlensing technology. The KAF-3200ME has excellent quantum efficiency between 350 nm and 1000 nm with significant enhancement at the blue end of the spectrum. Low dark current and high pixel charge capacity results in a dynamic range exceeding 77 db. The KAF-3200 has the highest Quantum Efficiency and lowest noise of any Kodak sensor, making it exceptional for low-light applications where maximizing the available Signal to Noise Ratio (SNR) is paramount. With peak QE of over 80-percent, it offers many of the benefits of a back-illuminated sensor without the drawbacks or higher cost.
Kodak KAF-3200ME Specifications:
*CCD Architecture: Full Frame
*Imager Size: 14.85 mm Wide x 10.26 mm High
*Pixel Array: 2184 x 1472 active pixels
*Total Number of Pixels: 3.2 megapixels
*Pixel Size: 6.8 microns x 6.8 microns
*Quantum Efficiency: Peak: 82-percent
*Pixel Dark Current: <0.5 electrons per second at 0 degreesC
*Intrinsic Read Noise: 7 electrons RMS
*Charge Transfer Efficiency: >0.99999
*Dynamic Range: 77 db
About QSI Two-Stage TEC Cooling:
The QSI 632wsg has a very efficient custom 2-stage thermoelectric cooler (TEC) subsystem. Intelligent, programmable cooling fans are integrated into the rear of the camera body to remove the heat generated by the cooler. Typically, forced air cooling lowers the regulated CCD temperature by up to 45 degreesC below ambient utilizing 85% power. Tight +/- 0.1 degreesC temperature regulation is maintained at temperature settings of 10 degreesC below ambient and lower. A slim liquid heat exchanger (sold separately) can be attached to the rear of the camera body to increase the cooling further, up to 55 degreesC below the temperature of the circulating fluid.
The cooled CCD image sensor is positioned in a hermetically sealed environmental chamber and covered with an anti-reflection precision optical window. The sealed chamber is purged with an ultra dry noble gas to increase heat conduction and eliminate the possibility of frost forming inside the chamber. To extend the useful period before re-purging is required, a user-rechargeable micro-sieve desiccant is employed to scavenge water molecules that enter the chamber. It is located behind a sub-micron, gas-permeable membrane to prevent particulate contamination of the CCD chamber.
QSI Integrated Guide Port WSG Upgrade:
The QSI 600 Series WSG cameras provides a solution to the problems normally associated with guiding by integrating a Guider Port directly into the camera body. The pick-off prism is designed to sit in front of the filters so that you will always have all the star's light available for guiding.
The large 1/2 square pick-off prism of the integrated guide port is optimally positioned close to the internal filter wheel, supporting the use of guide cameras with large sensors, while preventing any vignetting of the main sensor, even with very fast optical systems. The Integrated Guide Port (IGP) is designed to support any camera with 12.5 mm of back focus or less that can be attached using C-mount or T-mount threads.
The threaded adapter sits on top of the focus ring and allows the guide camera to be rotated to any position. The focus ring threads onto the focus base to allow 3mm of travel when focusing the guide camera. Once focus is achieved, the focus ring is locked with a set screw. The guide camera can still be rotated manually if desired without changing the focus. The end result is a rigid, easily focused guide camera that will not move or flex while your mount tracks the apparent motion of the night sky.
OPT Product Number: QS-632WSG
QUESTIONS & ANSWERS
Have a Question?
Be the first to ask a question about this.